![]() ![]() Hardware Station Crd Hdw Net-Interface NM MAC HP-DLPI DLPI 메뉴는 SAM -> Network and Communications -> Network Interface Cards(NICs) -> 해당 Interface Card 선택(Space Bar 또는 Click)후 Actions 메뉴에서 Modify 메뉴를 선택 후 변경한다.다만 변경시에 일시적으로 Network Interface Card(LAN Card)의 reset이 발생하여 Network 이 잠시 중단된다. Lan 0 10/0/12/0 btlan3 CLAIMED INTERFACE HP PCI 10/100Base-TX Core Stats clear Clear all driver and adapter statisticsĬlass I H/W Path Driver S/W State H/W Type Description Recv_coal_ticks Set receive interrupt coalescing ticks default 0 Send_coal_ticks Set send interrupt coalescing ticks default 150 Recv_max_bufs Set receive buffer coalescing threshold default 1 Send_max_bufs Set send buffer coalescing threshold default 10 ※ HP APA 구성 시 config 설정 주의 : stanby=on 확인ĭescription = lan0 HP PCI 1000Base-T Release B.Ĭlearing LAN Interface statistics registers.Īuto_on Set the card in autonegotiation modeĪuto_off Turn off Auto-Negotiation mode for a 1000Base-SX cardġ0hd Set the speed of a 1000Base-T card to 10 Mbps half-duplexġ0fd Set the speed of a 1000Base-T card to 10 Mbps full-duplexġ00hd Set the speed of a 1000Base-T card to 100 Mbps half-duplexġ00fd Set the speed of a 1000Base-T card to 100 Mbps full-duplex Reset = Reset LAN Interface to execute its selftestĭescription = lan0 HP PCI 1000Base-T Release B.11.11.21 Quit = Terminate the Administration, return to shell ![]() LAN Interface PPA Number = 0ĭisplay = Display LAN Interface status and statistics registersĮnd = End LAN Interface Administration, return to Test Selection well, I don't know, check the above and update the question.LOCAL AREA NETWORK ONLINE ADMINISTRATION, Version 1.0 If its the closest then maybe DHCP is being stopped by the first switch - so if you can manage the switch using the address you see then check the configuration of the switch and fix it. Then you can tell which switch is getting an address If its not 192.168.0.239 then check your DHCP server configuration page on the draytek 2860 and see that the address is being issued and to which MAC - hopefully it matches that on a label on the outside of switch - the last octet may be different from what you see on the network as each VLAN needs a different MAC address. If this is so then they probably are "fighting" over the address - in that they will all respond to ARP requests and whichever is last will win, This makes it very difficult to connect to them. Finally what address do you get for the GS105Ev2 switch that you see - if its 192.168.0.239 then I believe all three have not got DHCP server assigned address and so have the same IP address and so only one will show up. First what is your DHCP server giving out? Second this does not include 192.168.0.239 which is the default for both switches so change that. Switches do not need an IP address to operate as a switch - the purpose of giving a switch an IP address is for management access to the switch - so the switch will work as a switch even if it has bad or unreachable IP addressesįor both the GS105Ev2 and the GS716T the switch will either get a DHCP address or if it cannot then get the address 192.168.0.239/24.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |